Brands
- AC
- ACA
- AMC
- Applied Test System
- Aro Scientific
- ASI Standard
- Cerulean
- Conidia
- Emcee
- Emco
- PAC
- PCS
- Phase Technology by PAC
- Pnshar
- PolyScience
- PulMac
- Regmed
- RISE
- Scavini
- Spectro Scientific
- Sundy
- Thwing Albert
- Tobias
- USON
- Vived Management JB
- Zematra
เครื่องวิเคราะห์ส่วนผสมของโลหะแบบตั้งโต๊ะ Arc Spark Spectrometer : OE Series

High-performance metals analysis made affordable
The OE750 and the NEW OE720 are ground-breaking OES metals analyzers. They cover the complete spectrum of elements in metal* with low detection limits and state-of-the-art multi-CMOS technology.
Tightening of industry regulations, complex supply chains and increased use of scrap as a base material means it’s crucial for foundries and metals manufacturers to control main, residual, tramp and trace elements in the lowest ppm range. Historically, OES analysis at this level was out of reach for many businesses. That’s now changed with the OE series.
These spark spectrometers allow you to analyze all main alloying elements and identify exceptionally low levels of tramp, trace and treatment elements in metals, such as nitrogen in steel. The OE750 also covers rare applications like oxygen in copper and oxygen, nitrogen and hydrogen in titanium.
Fast measurement times, high reliability and low operating costs mean the OE series is invaluable for everyday analysis and total quality control, with performance on a par with larger and more expensive spectrometers.
*Depending on the application, for further details request our application reports.
- Specification
- Standard
- Model
Optical system
> LightWing technology: Multi-CMOS optics in Paschen-Runge mounting and optimized pixel resolution
> Focal length: 400 mm
> Wave length: OE720: 174 – 670* nm / OE750: 119 – 670* nm (*766 nm on request)
> Peak position alignment
Typical applications
Quality control for process and melt verification: analysis mode / grade identification
All relevant alloying, residual, treatment, trace and tramp elements with low limits of detection
> Fe: Alloys, cast iron alloys incl. N down to 10 ppm (OE750 only)
> Al: Alloys, cast alloys, wrought alloys…
> Cu: Bronze, Brass, Cu-Ni…
> Ni: hasteloy, inconel, monel, incl. N down to 20 ppm
> Ti: Ti pure, Ti.6-4, Ti.8-Mn, incl. gases such as H, O, N (OE750 only)
> Mg, Co, Pb, Sn, Zn alloys, solders and more
- Specification
- Standard
- Model
Optical system
> LightWing technology: Multi-CMOS optics in Paschen-Runge mounting and optimized pixel resolution
> Focal length: 400 mm
> Wave length: OE720: 174 – 670* nm / OE750: 119 – 670* nm (*766 nm on request)
> Peak position alignment
Typical applications
Quality control for process and melt verification: analysis mode / grade identification
All relevant alloying, residual, treatment, trace and tramp elements with low limits of detection
> Fe: Alloys, cast iron alloys incl. N down to 10 ppm (OE750 only)
> Al: Alloys, cast alloys, wrought alloys…
> Cu: Bronze, Brass, Cu-Ni…
> Ni: hasteloy, inconel, monel, incl. N down to 20 ppm
> Ti: Ti pure, Ti.6-4, Ti.8-Mn, incl. gases such as H, O, N (OE750 only)
> Mg, Co, Pb, Sn, Zn alloys, solders and more